8900
  • 【IMPORTANT NOTIFICATION】 Due to the signal attenuation, cable quality, PoE mode A/B mis-match or insufficient PoE budget from PoE Supply Units (very common in PoE NVR), our EOC Receiver and EOC-Transmitter may not be powered on. In this situation. Use LINOVISION Mini Passive 2 port PoE Extender, which acts as a PoE booster and PoE mode A/B converter perfectly solve these problems.
  • 【MODE A/B POE CONVERTER】 Connect LINOVISION Mini Passive 2 port POE Extender as a POE Booster and PoE mode A/B converter between POE Switch/NVR and EOC Receiver, you will get a stronger signal and compatible with Mode A & Mode B PoE.
  • 【PoE & IP OVER COAX CONVERTER】LINOVISION’s POE IP Over Coax converter can be used to upgrade analog system to IP surveillance system while using existing coaxial cable. Compatible with RG59, RG6, RG11 cables. Supports POE standards 802.3af (PoE) and 802.3at (PoE+). EOC Receiver MUST be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices
  • 【POE & IP OVER TWIST PAIR CONVERTER】 Each pair of EOC(Ethernet over Coax) Converter is equipped with 2 BNC to Twist Pair connectors, which enables POE over Twist Pair transmission. 100Mbps bandwidth over 330ft regular twist pair cables while 10Mbps over 1485ft for both POE or NON-POE devices. It’s ideal for the CCTV system in elevator cart.
  • 【POINT TO POINT CONNECTION ONLY】Act as MoCA (Multimedia over Coax) in point-to-point connection, transmit video/audio/data/control signal over coaxial cable, so as being used with twist pair. EOC Receiver should be powered by POE switch or POE injector while Transmitter should be connected with POE devices or NON-POE devices.
  • 【PASSIVER 2-PORTS POE SPLITTER】LINOVISION 2 ports POE extender is designed to supply POE power to two POE devices through one Cat5/6 cable, and no power adapter is required. It is powered by PoE devices (48V or 53V PoE Switch/PoE NVR/PoE Injector/Mid-span). With this POE splitter, the cabling cost can be dramatically reduced. Moreover, users can easily add extra POE device (like IP cameras,or IP phones) to existing POE cable without running a new cable.
  • 【UP TO 1,000FT POE + DATA EXTENTION】Extra 330ft POE+Data transmission will be extended with one LINOVISION POE Extender. And it supports two levels cascade deployment, therefore total 1,000ft POE + Data transmission is provided. (The 2nd POE Extender’s POE Input should be connected to the 1st POE Extender’s Out port, not Camera port)
SKU: EOC+POE Extender02
POE IP Over Coax Converter banner

3 Main Reasons to Use Linovision POE IP Over Coax Converters

Reason 1
Upgrade traditional analog camera system to IP surveillance system without replacing existing coaxial cable (RG59 cable)

Reason 2
PoE Extend up to 3,000ft without repeaters

There are some situations that users need to transmit PoE power and data over ultra long distance, for example, power a remote security camera from 500 meters (or 1,640ft) away (from one building to another building), or supply power to a PoE IoT device from one side to another side of an underwater tube. The regular PoE extender will extend 100 meters only. With Linovision innovative EOC solution, it makes this possible to transmit PoE power and data over max. 1,000 meters (or 3,300ft) through regular Cat5e or Cat6 cable, this will reduce thousands of dollars in cabling cost.

Reason 3
POE +Data Transmission over Twisted pair cable, coax cable, telephone cable, doorbell camera, or any two-pin cables

There are some locations that without network cables but still need POE power and data transmission, for example elevator carts in many buildings, or doorbell cables, LINOVISION EOC converters is perfect for this application. It can transmit POE power and IP data over coax RG59 cable, twisted pair cable, doorbell cable, telephone cable, or even power cables. The remote connected device can be IP cameras, IP Video intercoms, IP phones, or IP controllers, etc.

EOC (Ethernet Over Coax, also known as IP over Coax) Converter is used to transmit Video & Audio & Data over existing coaxial cables.Features with
POE & IP data transmission, LINOVISION EOC converter is designed to upgrade traditional analogue video surveillance system to IP surveillance
system without replacing coaxial cables. It is working with POE IP cameras, POE Wi-Fi AP, VoIP phones, etc.
Linovision EOC Unique Features


Unique Features compared with other products in the market

  • POE + IP Data transmission over Coaxial cable, perfect for IP CCTV system.
  • Industrial design, with built-in heat sink, ensure super reliability and hassle-free transmission.
  • Up to 100Mbps in 300m (1000ft) RG59 cable transmission, max 1000m (3000ft) distance in 10Mbps.

2022 Updated Version

The 2022 version EOC converter supports POE IP data transmission over twist pair cable, such as Cat5E/Cat6 cable, power line, RS485 cable, etc.
BNC to Twist pair connectors are required in this connection. This function is widely used in elevator application.

Outstanding Features:

  • IP Video & Audio & Data & POE Power transmission over coaxial cable.
  • Passive design, no power adapter is required.
  • Max 1000 meters (3000ft) transmission.
  • Upto 100Mbps bandwidth over 1,000 feet regular coax cable transmission, working with CCA/CCU RG59/RG6 cable.
  • Plug-and-play, configuration free.
  • Small size (3.1“x2.0”x0.9“), light weight, fit into regular cameraback box.
  • Compatible to IEEE802.3af/IEEE802.3at POE protocol, max 21W POE load capacity in 100m (330ft) , or 11W POE load capacity in 300m (1000ft).
  • Optional water-proof box for outdoor use.
  • Working with POE IP Cameras, POE Wi-Fi AP, VoIP phone, etc.
  • 1 * RJ45 port:10/100Mbps, MDI/MDIX self-adaption; 1 * BNC RG59 coaxial.

EOC Connection Diagram
EOC Transmission Performance form

EOC Transmission Performance

  • This chart of transmission performance is based on regular RG59 coaxial cable and powered by standard DC48V POE injectors.
  • The performance will be better when using RG6 cable or DC53V POE injectors.
  • This EOC transmitter and receiver can transmit up to 100Mbps network data and load max 11W POE device in 300 meters (or 1,000ft).
  • The network bandwidth will be automatically lowered to 10Mbs over 1,000ft and the max transmission distance is 3,280ft. This bandwidth is still sufficient for single 4K IP camera.

EOC Application for single IP Camera
EOC Application for single IP Camera
  • Upgrade traditional analogue system to IP surveillance system while using existing coaxial cable(RG59 cable)
EOC Application for VoIP Phone; WiFi AP
EOC Application for VoIP Phone; WiFi AP
  • Remote power & network transmission for VoIP phone, WiFi AP (POE enabled) over coaxial cable
EOC Application in Elevator
EOC Application in Elevator
  • Transmit POE power and IP data over coaxial or twist pair cable. One passive EOC-transmitter will be put inside the elevator cart to feed camera or signal board, and one EOC-receiver will be in the control room, powered by POE switch/POE injector/POE NVR.
  • For multiple elevators application, one EOC-Switch04 or EOC-Switch24 will be put in the control room, working together with max 8 elevators.

Ethernet & POE Extender is used to extend Ethernet and POE power transmission distance through Cat5E/Cat6 cable. Features with passive design and unique 2 ports output, Linovision POE-Extender02 can not only extend ethernet and power transmission, but also simplify cabling by running one cable to power two POE devices, such as POE IP camera, VoIP phone, door bell camera, etc.
POE Extender Connection Diagram

Outstanding Features

  • Passive Ethernet & Power extender/repeater/amplifier for 100m (330ft), no power adapter is required.
  • Unique 2-port POE outputs, running one cable to connect to 2 IP devices, or 3 IP devices with cascade deployment.
  • Cascade deployment when working with 60W POE Injector/Midspan.
  • Plug-and-play, configuration free.
  • Small size (3.1“x2.0”x0.9“), light weight, fit into regular camera back box.
  • Compatible to IEEE802.3af / IEEE802.3at POE protocol.
  • Optional water-proof box for outdoor use.
  • Working with POE IP Cameras, POE Wi-Fi AP, VoIP phone, etc.
Application 1
  • One cable to power two IP cameras or PoE devices through one Cat5E/Cat6 cable
Application 2
  • Cascade deployment, powering 3 POE devices through one Cat5E/6 cable
  • 60W POE Injector or Midspan is required for cascade deployment
Application 3
Use PoE-Extender02 and EOC converter to power 2 IP cameras through one Coax cable
FAQ Related

Q1: Does this extender need an addition power supply?

A: No, it does not require local power supply. This POE extender is powered by PoE devices (48V or 53V PoE Switch/PoE NVR/PoE
Injector/Mid-span).

Q2: Do I need two of these to extend cat6 for 600 feet?

A: Yes, the POE extender supports cascade deployment, max 300m (1000ft) transmission and running one cable to support 3 IP devices, but 60W POE injector is required and IP camera power consumption should be less than 8W.

Q3: What is the load capacity of POE device that connected to this POE extender?

A: Basically, the load capability depends on the POE supply device, the total power consumption of two POE output is less than the POE power input. For example, if the POE supply unit is a 30W POE injector, then the total output power of this POE extender is less than 27W (with deduction of 3W power consumption by POE extender itself), the longer the transmission distance, the lower power output from POE extender. We recommend to use 60W High POE injector to connect to this POE extender.

You may also like